Polyurethane adhesive for high load floor coverings UZIN KR 430

Reliable bonding of rubber and sports surfaces

Universal two-component polyurethane adhesive for floor coverings with high loads.

Heavy duty polyurethane flooring adhesive, solvent free, with great adhesion, extremely reliable – good dimensional stability, no shrinkage.

It is used for almost any load, universal, with a very high final strength, high heat and frost resistance.

For internal and limited – external works.

Application area

For rubber coverings up to 10 mm thick (B1), with smooth back (A1), with sanded back (A2).

For linoleum on absorbent and non-absorbent substrates in sports halls, industrial and heavily loaded areas.

Application:
Free of solvents and water, 2
component adhesive based on reaction
resins for rubber, tile coating with
smooth or profiled substrate (such as
Norament), linoleum (Linodur type,
Marmoleum), rubber granulate coatings
(Regupol type), coatings such as artificial
grass, sports mats and outdoor surfaces,
as well as for sticking connecting tapes on
synthetic coatings, insulating
UZIN materials.
Suitable for absorbent, long-lasting dry
bases such as cement, anhydrite and
magnesite screeds, concrete, etc., and
non-absorbent, thermoplastic or
deformable bases such as cast
asphalt, chipboard, wood, aluminum, steel sheet
etc. Specially designed for coatings,
experiencing high mechanical stress –
in industrial, commercial premises,
sports fields and hospitals. Withstands
loads from stackers and wheel loaders.
Also glues fiberboard, dense foam, ceramics,
stone, etc.
For internal and limited for external
works, as well as for wet areas.
Attention: before sticking unchecked
PVC and rubber coatings, synthetics or
metals to carry out test gluing. At
use in wet areas or
consult the manufacturer from the outside. For sticking conductive
coatings, use UZIN-KR 430L adhesive.
Attention: not suitable for cemented
bases with high alkaline moisture,
e.g. standing directly on the ground
concrete foundations without waterproofing, etc.
Suitable for underfloor heating as well as for
chair loads on casters according to DIN 68 131.
Advantages/
Material properties:
UZIN-KR 430 – 2-section combination jar with
pasty gray component A (lower part
cans) and liquid dark brown hardener
(upper insert) After mixing both components
creamy paste, easy to apply
with a spatula, an adhesive without volatile components, which quickly
and solidifies uniformly into a high-strength, sealed
polyurethane mass with very high strength
grasping and binding on most grounds and
coatings.
• does not contain solvents and water
• fast curing
• fills cavities without shrinkage
• for any layer thickness
• hard elastic
• waterproof, weather resistant
• waterproof
• resistant to mechanical loads
Technical data:
Type of packaging: Combipack, set A+B
Packaging: 6 kg, 12 kg
Guarantee. shelf life: approx. 12 months
Color: gray
Density: 1.40 kg/l
Processing temperature: not below.150C on the floor
Consumption: 300-1300 g/m
2
Drying time: 20 – 30 min.*
Styling time: 30 – 40 min.*
Load ready: 24-48 hours*
Final strength: after 7 days*
* at 200C and normal conditions

Foundation preparation:
The base must be clean, durable
dry, even and without cracks, and also durable
for bending and compression. Coatings and bases
must provide the intended
mechanical stress on them. uneven
primed substrates, e.g. dispersion
primer UZIN-PE 360 and cover with a layer
cement putty, eg. UZIN-NC 170 or
UZIN-NC 172. Elastic bases, e.g.
rubber granulate, putty with polyurethane putty UZIN-KR 410. Small
Irregularities can be leveled with glue itself. For
direct sticker on
non-sanded absorbent substrates
need to be covered first.
waterproofing primer UZIN-PE 460.
Dense smooth bases such as ceramics,
stone, metal, etc. must be degreased
or clean up. For reaction resin systems
type UZIN-PE 460 (also sanded)
or UZIN-KR 410 (if necessary
sanded) gluing should be
produce within 1-2 days to
provide sufficient binding with not yet
fully cured surface.
materials.
Processing:
Pierce the compartment in several places
hardener B and allow it to drain completely into
jar of resin A, then remove the compartment
component B and stir the mixture until
until it turns into a homogeneous mass.
Use a low speed stirrer
spiral or frame nozzle. Avoid
bubble formation. Emphasize on
mixing of the mass next to the walls and
the bottom of the bank. In special cases for quick
hardening can be added approx. 0.1%
accelerator for

i polyurethane uzin.
Spread the adhesive evenly with a notched trowel
to the surface. Spatula teeth required
choose according to the required
amount of glue, for example:
Sanded substrate A2, B1 450 – 550 g/m
2

Profiled substrate B3, No. 21 800 – 1000 g/m
2
Lay the coating, rub well, with
need to load. In 2-3 hours
roll with a heavy roller. self coating
must lie flat so that the reaction adhesive
in the initial phase of setting did not show
pulling force. Calculate Quantity
glue so that the smooth substrate
coating was completely covered with glue, but
So. so that the coating does not “float”. at
applying glue to the profiled substrate
take care not to let
penetration of surface water (cleaning
funds) in places of greatest load.
Important instructions:
• Materials should be stored in their original packaging in a dry
place ok. 12 months. optimal conditions
storage 15-250С. When stored cold
components become viscous, so before
use, it is necessary to bring them to room temperature.
temperature. If the component has thickened, the product
cannot be used.
• The coating must not be laid at temperatures
floor or material below 150C, and/or
relative humidity above 75%.
Low temperatures impair adhesive mixing and
slow down its curing.
• To clean the instrument immediately after
use and to remove fresh dirt
resin, use the UZIN-VE 100 cleaner.
(Warning: dissolves synthetics!) or UZIN-VE
124. Hardened material can be removed
only mechanically.
• Recommended standards and regulations: DIN
18365 “Work with floor coverings” /
Adhesive Industry Association Instructions “Assessment and preparation of grounds for
elastic and textile floor stickers
coatings” / Information of the central union
German builders (ZDB) “Elastic
floor coverings, textile flooring
coatings and parquet on floor structures with
heating.”
Labor and environmental protection:
Component A is not hazardous.
Component B contains diphenylmethane diisocyanate!
Follow instructions and warnings on
product packaging. May irritate eyes
respiratory organs and skin. Possible allergic
reactions by inhalation and skin contact.
Avoid breathing vapors (steams when heated
jars!) When working, use protective
skin creams, as well as protective clothing,
shoes and glasses. Provide good
workplace ventilation. Skin contact
wash immediately with soap and water. at
contact with eyes, rinse with plenty of water and
see a doctor. Cured polyurethane
mass is completely safe.
Additional requirements: specification M
044 chemical union/technical specifications
security UZIN-KR 430/
Waste disposal:
Completely drained, no residue
hardener, dry the jars (hardener residues
react on contact with water or slowly with moisture
air), waste code 35105. Mixing jar
completely drain (clean with a scraper), jar
dispose of according to waste code 35106. Remaining components
Collect A and B, allow to react and dispose of as
construction garbage. Banks with unhardened
components to be disposed of as special waste (code
waste 35106). Do not pour into sewers, watercourses or
to the ground.
These figures are based on our thorough research and
experience. Various conditions at construction sites and methods
treatments affect laying work. Their success depends on
your professionalism, practical experience, as well as from
careful observance of the operating instructions.
Please follow the instructions in the information
floor covering manufacturers. With the advent of this
product information, all previous instructions become null and void.